How To Install Weiser Smart Key Lock
Installation and User Guide
Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.weiserlock.com/doorprep
Measure to ostend that the pigsty in
the door is either two-1/viii″ (54 mm) or 1-1/2″ (38 mm).
Measure to confirm that the backset is
either 2-iii/8″ or 2-3/4″ (threescore or lxx mm).
Measure to confirm that the hole in
the door edge is one″ (25 mm).
Measure to confirm that the
door is either one-3/8″ or 1-3/four″ (35 mm or 44 mm) thick.
Note: Boosted door preparation may be
required for doors with 1-i/2″ (38 mm) holes.
Consult the deadbolt drilling instructions at
www.weiserlock.com/doorprep
Install the latch and strike
Hold the latch in front of the door pigsty, with
the latch confront affluent against the door edge.
Is the slotted hole centered in the door hole?
No adjustment is
required. Go along
to adjacent stride.
Rotate latch face as
shown to extend latch.
Is the door border chiseled?
Optional: Utilise a flathead
screwdriver to elevator tabs on collar
of rectangular face up to remove
square corner face and replace
with round corner face (if needed).
Utilise a flathead screwdriver to
elevator tabs on neckband of rectangular
face to remove it from latch.
Install drive-in collar.
Install strike on the door frame with the longer
screws closest to the door jamb.
Brand sure hole in door frame is drilled a
minimum of 1" (25 mm) deep.
Important: Make sure the latch bolt is fully
retracted (in the unlocked position).
Set up keypad and mounting plate (simply for doors with smaller holes)
What is the bore of the hole in the door?
No adjustment is required. Go on to step 4.
Remove adapter ring from exterior assembly:
Use pliers to remove 2 tabs from mounting plate:
Install exterior assembly
Route t A he cable below the latch.
IMPORTANT: Make sure the latch is fully
retracted (in the unlocked position).
IMPORTANT: Make sure the torque
bract is in the horizontal position.
Insert the torque bract through the
horizontal slot in the latch.
IMPORTANT: Hold the exterior assembly
on the outside firmly (or have a 2d
pair of easily) for the next steps.
Push the torque blade through the center
hole in the mounting plate and send the
cable through the bottom hole.
Secure the mounting plate with the supplied screws.
Insert the cardinal and exam the latch
for shine performance.
Remove the primal and make certain the latch
commodities is yet in the unlocked position.
Install interior assembly
Remove the bombardment cover
Load iv AA batteries into the interior assembly. For best results, utilize new, non-rechargeable Alkaline batteries only.
Press and hold the Reset button on the interior associates for 5 seconds, until you hear three long beeps.
Align the colored edges of the connectors and ensure a tight cable connection.
IMPORTANT: Rotate the turnpiece AWAY from the door border and make sure the latch is fully retracted (in the unlocked position).
Make certain the torque blade is still in the horizontal position and install the interior assembly.
Test the turnpiece for smooth rotation.
Secure the interior associates with the supplied screws.
Reinstall battery cover and make sure the latch is still in the unlocked position.
Set locking and unlocking management
While the door is OPEN and UNLOCKED, enter the following code to teach the lock the orientation of the door:
This is your default Mastercode.
Note: Each button on the keypad represents ii numbers. Yous only need to push the button once to go either number.
- Press 0-0-0-0.
- Press
You will hear one beep. - Press 0.
- Press
The latch bolt will extend and retract. The lock volition beep and the keypad will turn green or red.
Press the Lock button. The latch commodities will extend to lock.
Enter the default User Code (i-two-three-4), and then press the Lock button. The door will unlock
IMPORTANT: It is recommended that you lot supplant the default
Mastercode and default User Code with codes of your own. Meet page 4.
Optional: Re-central the lock
If needed, re-key the lock to piece of work with your existing key. Come across the supplied SmartKey Re-Key instructions for more data
Quick Setup and Employ
Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and yous volition need to restart the procedure.
Circumspection: A User Code is used to unlock the door while a Mastercode is a password for making changes to the lock features.
- Make certain the lock is unlocked and the door
is open. - Enter your existing Mastercode – for new install,
default is 0-0-0-0. - Press You will hear ane beep.
- Press v.
- Press You volition hear two beeps if successful. If you hear 3 beeps, it was unsuccessful. Repeat from footstep 1 slowly.
For a new installation, this will delete the default User Code 1-2-3-iv. For subsequent instances, this will delete all User Codes in the lock.
Now the lock can only be operated by the key and turnpiece until a new User Code is added in step B.
How to add User Codes
A total of 6 User Codes (and a temporary one-fourth dimension User Lawmaking) may be programmed. Practise not program a User Code that is the same every bit your Mastercode.
Circumspection: A User Lawmaking is used to unlock the door while a Mastercode is a password for making changes to the lock features.
- Brand sure the lock is unlocked and the door
is open. - Enter your Mastercode – for new install,
default is 0-0-0-0. - Press You lot volition hear one beep.
- Press 1.
- Printing You will hear one beep.
- Enter a new User Code. It must be iv-ten digits.
- Press .You lot will hear ii beeps if successful. If you hear three beeps, it was unsuccessful. Echo from
step ane slowly. - Exam the code: While your door is open, lock it. Enter your new User Code, then press The door should unlock.
How to alter your Mastercode
The Mastercode will non unlock your door. It is an added security feature that is used to set up all functions.
The default Mastercode is 0-0-0-0. It is recommended that you modify it to a lawmaking of your ain.
- Make sure the lock is unlocked and the door is open.
- Enter your Mastercode – for new install,
default is 0-0-0-0. - Printing You will hear one beep.
- Press vii.
- Press Yous will hear one beep.
- Enter a new Mastercode. It must be between
4 and 10 digits. - Printing Y'all volition hear two beeps if successful. If you hear iii beeps, it was unsuccessful. Echo from step i slowly.
Boosted Programming Features
How to enable/disable Auto-Lock
The Auto-Lock feature automatically re-locks your door thirty seconds after unlocking. This feature is off past default.
- Make sure the lock is unlocked and the door
is open. - Enter your existing Mastercode.
- Press You will hear i beep.
- Press 1 – 1.
- Press You will hear two beeps if successful. If y'all hear 3 beeps, it was unsuccessful. Repeat from footstep one slowly
How to change Automobile-Lock time delay
Yous can set the Motorcar-Lock time delay to 10, 20, 30, 40, or 50 seconds.
- Make sure the lock is unlocked and the door
is open. - Enter your existing Mastercode.
- Printing You will hear one beep.
- Press 1 – 3.
- Press You will hear one beep.
- For ten seconds, printing ane.
For twenty seconds, printing 3.
For thirty seconds, press v.
For 40 seconds, press 7.
For 50 seconds, press 9. - Press You lot will hear two beeps if successful.
If you hear three beeps, information technology was unsuccessful.
Repeat from step 1 slowly.
How to enable/disable User Codes
If User Codes are disabled (example: when y'all keep vacation), the lock can only be operated by the primal and turnpiece until they are enabled again.
- Make sure the lock is unlocked and the door is open.
- Enter your existing Mastercode.
- Press Yous will hear 1 beep.
- Press one – 7.
- Press Yous will hear two beeps if successful. If y'all hear three beeps, it was unsuccessful. Repeat from pace 1 slowly.
How to delete private User Codes
The lock is pre-programmed with a default
User Code of 1-two-three-4. Information technology is recommended that yous delete this lawmaking.
- Make sure the lock is unlocked and the door
is open. - Enter your existing Mastercode.
- Press You will hear 1 beep.
- Press 3.
- Press You volition hear one beep.
- Enter the User Lawmaking you wish to delete.
- Printing Yous will hear two beeps if successful. If you hear three beeps, it was unsuccessful. Repeat from stride 1 slowly.
- Test the code: While your door is open, lock it. Enter the User Code, then press The door should not unlock.
How to add together a one-time User Code
A i-time user code may be used only once, and then it will exist deleted immediately afterward use.
- Make sure the lock is unlocked and the door is open.
- Enter your existing Mastercode.
- Press You will hear one beep.
- Press 1 – 9.
- Press You lot will hear 1 beep.
- Enter a new User Lawmaking. Information technology must be four-10 digits.
- Printing You will hear ii beeps if successful. If you hear three beeps, it was unsuccessful. Repeat from step one slowly.
How to mute/unmute lock
If the lock is muted, y'all volition not hear beeping during programming, normal operation, low battery indicators, or system alerts.
- Make sure the lock is unlocked and the door is open.
- Enter your Mastercode.
- Printing You volition hear 1 beep.
- Press 1 – v.
- Printing You will hear two beeps if successful. If y'all hear 3 beeps, it was unsuccessful. Repeat from step 1 slowly.
How to restore default settings
This procedure will delete all User Codes associated with the lock, and the default Mastercode (0-0-0-0) and User Lawmaking (one-2-three-4) will be restored.
- Brand sure the door is open up and unlocked.Press and agree the Reset push button for v seconds, until y'all hear 3 long beeps.
- Enter the default Mastercode (O-O-O-0).
- Press You will hear 1 beep.
- Printing 0.
- Press The latch bolt will extend and retract to learn the orientation of the door. If successful, the keypad will flash green and you volition hear 2 beeps. If unsuccessful, the keypad will flash red and you lot will hear 3 beeps (make sure the door is open and unlocked and that y'all are using a fresh set of batteries).
- Test the lock: With the door open and unlocked, press .
Make sure it locks the door. - Examination the default User Code: Enter the default User Lawmaking (one-2-3-4), then press Make sure it unlocks the door.
The default Mastercode is 0-0-0-0. Information technology is recommended that you change it to a code of your ain.
The lock is pre-programmed with a default User Code of 1-two-3-4. It is recommended that you delete this lawmaking.
Arrangement Alerts
Regulatory Compliance
This production complies with standards established by the post-obit regulatory bodies:
- Federal Communications Commission (FCC)
- Industry Canada
FCC
This device complies with Function 15 of the FCC Rules. Operation is subject field to the following two conditions:
( 1 ) this device may not cause harmful interference, and
( 2 ) this device must accept whatever interference received, including interference that may crusade undesired functioning.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part fifteen of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and tin can radiate radio frequency free energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, in that location is no guarantee that interference will non occur in a particular installation. If this equipment does cause harmful interference to radio or tv reception, which tin be adamant by turning the equipment off and on, the user is encouraged to effort to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit unlike from that to which the receiver is continued.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modifications not expressly canonical by the manufacturer could void the user's authority to operate the equipment.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is field of study to the following ii conditions: ( 1 ) this device may non cause interference, and ( 2 ) this device must accept any interference, including interference that may cause undesired operation of the device.
Troubleshooting
The lock cannot be locked or unlocked by the keypad.
Make sure the lock is programmed with at least one User Lawmaking and that the User Codes are not disabled. If needed, restore the lock'south default settings.
The keypad doesn't reply when touched (no lights are visible and no beeping is heard).
Make sure the cables are properly continued, and make sure the batteries are new and installed correctly.
The door can be locked with the Lock button, but the User Lawmaking volition non unlock the door.
Brand sure the User Code is correct and that the Lock push is pushed after entering the User Lawmaking. If the door still won't unlock, use a cardinal to unlock the door. Call technical support for further troubleshooting.
When the door is closed and the Lock button is pressed to lock the door, the lock beeps 3 times. When the door is open and the Lock button is pressed to lock the door, the lock doesn't beep.
Make sure that the hole in the door frame backside the strike is drilled at least 1 inch (25 mm) deep. Also make sure the strike plate is aligned with the latch bolt. If needed, reposition the strike.
Important Safeguards
- Read all instructions in their entirety.
- Familiarize yourself with all alarm and caution statements.
- Remind all family members of safe precautions.
- Restrict access to your lock's interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
- Protect your User Codes and Mastercode.
- Dispose of used batteries according to local laws and regulations.
Caution: Foreclose unauthorized entry. This lock has a pre-set User Lawmaking and Mastercode. Upon installation and set-up, supercede both of these codes with your own. Since anyone with access to the interior assembly can reset the lock and change the User Codes, you must restrict admission to the interior associates and routinely check the User Codes to ensure they have not been altered without your knowledge.
WARNING: This Manufacturer advises that no lock tin provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and mutual sense. Builder's hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce run a risk, you should consult a qualified locksmith or other security professional
Source: https://captainlockpick.com/instructions/weiser/weiser-powerbolt-2-manual/
Posted by: walkergloold.blogspot.com
0 Response to "How To Install Weiser Smart Key Lock"
Post a Comment